How To Repair Drywall After Removing Tile

 I only recommend products I would utilize myself and all opinions expressed here are our ain. This post may contain affiliate links. and I may earn a small commission when y'all purchase from those links at no additional cost to you lot.

List Photograph of our Kitchen

I am then excited to finally share this series on our Kitchen Remodel. For the about function I did all of it myself, showtime to finish it took about a month. Below is a recent picture of the finished project. I just adore how bright and airy the room feels at present!

When we walked through our home for the first time I savage in dear with the bones of the Kitchen. At that place is an abundance of cabinet space as well as room for our whole family. Information technology is nestled perfectly between the formal and Casual sides of our home. Still it was drowning in yellowed maple cabinets with ornate grape vine detail AND the infamous 3D grapevine tile. Taking Eye stage was this large medallion above the stove. I lovingly named him George, and fantasized virtually the twenty-four hours I would rip him out. It was beautiful space, but information technology just wasn't our fashion.

Before Kitchen Updates

I knew rather quickly what I wanted to do with the space. I procrastinated for awhile, considering I knew how much work it was going to be. I was besides a little intimidated past tiling as I had never done it before. I have constitute with any large projects, the all-time thing I tin can practise is just START!

To kicking the series of I must get-go with the least glamorous part removing the backsplash and patching the drywall. I learned a lot forth the way so I take compiled some of my tips here and in the "Removing Tile & Patching Drywall" highlight on my Instagram.

Function 1 Removing Backsplash

Supplies:

1. Hammer
2. Sharp pry bar
3. Multi-tool
4. Fleck plywood
5. Safety Goggles
6. Thick work gloves

In training I spent more time researching tiling than removing old tile. I learned the hard manner how like shooting fish in a barrel it is to damage the drywall behind.

Our Tiles were pretty thick and attached to a thin paper-thin sheet. The Key is Non using the wall for leverage. Once you have, it damages the drywall behind. I establish one time I damaged the dry wall information technology was really difficult to get more than tile off without damaging more than dry out wall.

I found information technology best to get the abrupt edge of the pry bar nestled between that cardboard (or wall) and the tile. So give it a difficult tap on the back side of the pry bar. It is important to keep the pry bar perpendicular to the wall, and making sure the force is towards to tile. If done correctly the tiles volition pop off without damaging the wall. This step took some patience and A LOT of muscle.

Side note: I actually vigorously hammered and then much that I created a "mass" which resulted in my showtime mammogram and a few ultrasounds. Clearly I don't piece of work out my upper body very frequently. I was grateful we had already met our deductible for the year. 🤦‍♀️

Tip: I did use my dremel tool a couple times sharpen the edge of my pry bar. It really took a beating.

Information technology may leave some remnants behind, but those are easy to scrape off using a multi-tool. You can meet where I damaged the dry out wall in some of the areas.

It is really important to utilize condom goggles and proficient work gloves. The tiles really fly if you lot are doing it right, and they get actually abrupt. I besides had a piece of scrap ply wood where I was working. It helped protect the counters and appliances. I had a spare garbage handy so I could hands slide a lot of the rubble right from the ply wood into the garbage.

Part ii Repairing Drywall

Supplies

1. two′ x ii′ Drywall sheets (i/2″ , 5/8″ )
2. Utility Knife
3. Metal Ruler
4. Drill
5. Dry out Wall Screws
6. Measuring Tape
7. Multi-tool
8. Dry Wall Pocketknife
9. Mud
10. 12 " Militarist (Long apartment dry wall tool)
11. Sanding Square
12. Dry out wall record
13. Firing strips
14. Affiche Lath (Optional)
15. Pen
16. Tape drape
17. Joint Pocketknife
18. Mask

Patching Dry wall

Once the backsplash was removed, I had several areas of dry wall to repair. At one point I questioned whether I should accept just removed the dry wall with the tile.

I was pretty intimidated by dry wall repairs. Fortunately, I found Ralph at Home Depot to guide me. They keep all of the supplies in one department then information technology made it easy to get together everything I needed.

I started in 1 corner and but worked my way out. I used two'x2′ drywall sections for a couple of reasons. They are lighter and easier for me to handle by myself. They also made it piece of cake to clamper the sections out. I take a ton of outlets in the kitchen and so I didn't have to practice as much measuring this manner. Brand sure you lot measure the thickness of your existing dry wall so you get the correct size.

Taking ane section at a time I would identify whatsoever areas that had obvious holes or were weak. It is important to have a solid surface for the tile, otherwise it can crevice! I used my metal ruler and a sharpie to mark those areas. If at that place was no stud behind I used the drywall knife to cut out damaged sections.

If cuts were on a stud I used the utility knife to score the peak paper of the dry wall. And then I used the hammer and multi-tool to chiseled downward to the stud. I followed that with the utility knife again to brand a squeamish clean edge.

If there was a smaller hole with no stud behind it I used a slice of firing strip to provide back up. I wiggled information technology into the hole, then just put a screw through a good department in a higher place and below the hole. And then I could but put my patch right over that.

I actually had some left over affiche lath on hand from another projection, only I establish it especially handy. The kitchen is full of outlets. I made a template that measured exactly from the counter superlative up to the outlet and effectually.

Once I cut my section of dry out wall to size I measured the altitude from one side to the edge of the outlet. I used that measurement and my template to trace where the outlet hole needed to be.

I used the metallic ruler and Utility pocketknife to score around the unabridged hole. So I used a drywall pocketknife to cut three sides. Once the 3 sides were cut I would punch the dry wall and it would bomb out. I took some screen shots from my IG stories, simply in that location are a lot of these tips in action on there.

A little tip, once you cut one side of the paper you lot tin can just hit the drywall and information technology will divide. Then you lot can bend up that slice and use a utility knife to split the pieces like the prototype below.

I repeated this process effectually the entire room until I had all the sections patched. I used my multi-tool to scrape of all of the backlog mortar, cardboard from the previous tile, and stray dry out wall paper pieces. I wanted information technology to be as clean and smooth as possible, before I skim coated. Boy was information technology ugly at this footstep.

Role 3 Mudding Joints and Skim Glaze

In one case it was all cleaned up I put my drape tape all around to protect the counters. You tin see information technology was a piffling bit of absolute chaos.

I cleaned up daily so nosotros could however use our kitchen. Removing the tile and patching the backsplash was by far the messiest part of the kitchen renovation. That dry wall creates a lot of dust!

It is really of import to tape all of the seams. If you skip this stride your tile may crack!

One time taped seems embrace them with a thin glaze of mud. I was very careful to keep the tape in place. I tried to go on the mud equally shine equally I could. It doesn't have to be perfect though, because yous will sand later.

Once that layer of mud was dry out, I used my sanding block to polish any bumps or ledges. So I did an entire skim coat over everything. This office was really really fun, and reminded me of frosting a cake.

So I used my sanding cake to shine. I did at least 2 coats, and in some places 3 to ensure I would have a nice polish surface to utilize the backsplash. I waited a day betwixt each coat of mud to ensure it was completely dry, then sanded smooth. I waited a few days before actually applying backsplash to ensure it was dry.

Like I said this wasn't the most glamorous part of the project. Similar almost projects I made more of a mess before it started looking pretty again.

Up next in the serial I volition walk through how I tiled the backsplash. I learned a ton of great tips during this process!

Source: https://madewithgraceandgrit.com/2019/01/15/removing-backsplash-and-repairing-drywall/

Share this post